Category: ruthenium-catalysts

Adding a certain compound to certain chemical reactions, such as: 246047-72-3, name is (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium can increase the reaction rate and produce products with better performance than those obtained under traditional synthetic methods. Here is a downstream synthesis route of the compound 246047-72-3, 246047-72-3

After a 50 mL two-necked flask was purged with argon, the ligand 3be (10 mmol), CuCl (30 mmol, 3 eq) and 30 mL of dry DCM were sequentially added and the mixture was purged three times with argon to protect the closed system with argon balloon. Ruthenium complex 1b (12 mmol) was added under argon atmosphere, and the reaction was carried out at room temperature for 0.5 hour. After the reaction was over, silica gel was added to the filtrate to produce sand after filtration. The crude product was obtained by silica gel column chromatography and then washed with methanol or pentane-DCM to obtain 4be green solid product in a yield of 48%.

246047-72-3, The synthetic route of 246047-72-3 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Zannan Science And Technology (Shanghai) Co., Ltd.; Zhan Zhengyun; (102 pag.)CN104262403; (2017); B;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

15529-49-4, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.15529-49-4, Dichlorotris(triphenylphosphino)ruthenium (II) it is a common compound, a new synthetic route is introduced below.

General procedure: To a round-bottomed flask with a stir bar was placed with [Ru(PPh3)3Cl2] (868 mg, 2.0 mmol) under the nitrogen. Pre-dried THF(10 mL) was added and the resulting mixture was stirred at room temperature. Then salen-enH2 (536 mg, 2.0 mmol) and a little excess of Et3N (252 mg, 2.5 mmol) in THF (5 mL) were added. The reaction mixture was stirred at room temperature overnight. After removal of solvents, CH2Cl2 (15 mL) was added and the solution was filtered through cilite. The filtrate was concentrated and the residue was washed with Et2O (5mL 2) and hexane (5 mL 2) to give the desired product. Recrystallization from CH2Cl2/Et2O (1:2) afforded green block-shaped crystals of [RuCl(PPh3)(salen)] (3) suitable for X-ray diffraction in three days. Yield: 1011 mg, 76% (based on Ru).

With the complex challenges of chemical substances, we look forward to future research findings about Dichlorotris(triphenylphosphino)ruthenium (II)

Reference£º
Article; Tang, Li-Hua; Wu, Fule; Lin, Hui; Jia, Ai-Quan; Zhang, Qian-Feng; Inorganica Chimica Acta; vol. 477; (2018); p. 212 – 218;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.50982-12-2, Dichloro(cycloocta-1,5-diene)ruthenium(II) it is a common compound, a new synthetic route is introduced below., 50982-12-2

Separately, 200 ml of well dried tetrahydrofuran was fed to a 500 ml flask whose inside had been substituted by argon, and 5 g of dichloro(cyclooctadienyl)ruthenium was injected into the flask and well mixed with the above tetrahydrofuran to obtain a suspension. This suspension was cooled to -78 C. in a stream of argon, and 15 ml of the above synthesized tetrahydrofuran solution of trifluoromethyl cyclopentadienyl sodium was added dropwise to the suspension over 1 hour. The reaction mixture was further stirred at -78 C. for 3 hours and returned to room temperature under agitation over 12 hours. After the reaction mixture was let pass through a neutral alumina column in a stream of argon to be purified and concentrated, it was purified again by a neutral alumina column to obtain 0.2 g of bis(trifluoromethylcyclopentadienyl)ruthenium (yield rate of 30%)., 50982-12-2

As the paragraph descriping shows that 50982-12-2 is playing an increasingly important role.

Reference£º
Patent; JSR Corporation; US2006/240190; (2006); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

In the chemical reaction process, reaction time, type of solvent, can easily affect the result of the reaction, thereby determining the yield and properties of the reaction product.246047-72-3, name is (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium An updated downstream synthesis route of 246047-72-3 as follows., 246047-72-3

Grubbs’ second generation catalyst (226 mg, 1 eq) and copper (I) chloride (26 mg, 1 eq) were charged in a Schlenk tube and degassed. A degassed solution of compound C4 (26 mg, 21 eq.) in anhydrous dichloromethane (50 mL) was transferred via cannula to the solid. The mixture was heated at 30 C. for 60 min. The solvent was removed in vacuo and the residue was purified by chromatography on silica gel (PE/EA) to afford compound C5 (202 mg) as a green solid in 100% yield. 31P NMR (CDCl3, 161.8 MHz) delta (ppm) 22.88 (s, 1P); HRMS (ES+): m/z=764 (M+H+).

With the complex challenges of chemical substances, we look forward to future research findings about 246047-72-3,belong ruthenium-catalysts compound

Reference£º
Patent; Idenix Pharmaceuticals, Inc.; Parsy, Christophe Claude; Alexandre, Francois-Rene; Bonnaterre, Florence Marie-Emilie; Surleraux, Dominique; US9115095; (2015); B2;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.246047-72-3, (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium it is a common compound, a new synthetic route is introduced below., 246047-72-3

After a 50 mL two-necked flask was purged with argon, the ligand 3bv (10 mmol), CuCl (30 mmol, 3 eq) and 30 mL of dry DCM were sequentially added and the mixture was purged three times with argon to protect the closed system with argon balloon. Ruthenium complex 1b (12 mmol) was added under argon atmosphere, and the reaction was carried out at room temperature for 0.5 hour. After the reaction was completed, silica gel was added to the filtrate to prepare a sand product. The crude product was obtained by silica gel column chromatography, and then washed with methanol or pentane-DCM to obtain a green solid product 4bv. Yield: 90%.

With the complex challenges of chemical substances, we look forward to future research findings about 246047-72-3,belong ruthenium-catalysts compound

Reference£º
Patent; Zannan Science And Technology (Shanghai) Co., Ltd.; Zhan Zhengyun; (102 pag.)CN104262403; (2017); B;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

50982-12-2, As we all know, there are many different methods for the synthesis of a compound, and people can choose the synthesis method that suits their own laboratory according to the actual situation. 50982-12-2, name is Dichloro(cycloocta-1,5-diene)ruthenium(II) This compound is widely used in many fields, so it is necessary to find a new synthetic route. The downstream synthesis method of this compound is introduced below.

General procedure: The following common procedure was followed for the synthesesof complexes 1-5: A mixture of the ligand (0.36 mmol) and Ru(1,5-cod)Cl2(0.36 mmol) was dissolved in dry ethanol (10 ml) and the resultingmixture was refluxed for 2 h. The reaction volume was concentratedto a third of its original volume and the suspension was keptat 4 C overnight to give brick red solid which was filtered off,washed with cold ethanol and then diethyl ether. The solid wasdissolved in chloroform and excess of n-hexane was added toinduce the precipitation of the brick red solid product., 50982-12-2

The synthetic route of 50982-12-2 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Thangavel, Saravanan; Rajamanikandan, Ramar; Friedrich, Holger B.; Ilanchelian, Malaichamy; Omondi, Bernard; Polyhedron; vol. 107; (2016); p. 124 – 135;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Name is (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium, as a common heterocyclic compound, it belongs to ruthenium-catalysts compound, and cas is 246047-72-3, its synthesis route is as follows.,246047-72-3

Grubbs second generation catalyst (100 mg, 0.117 mmol), 2-[(2,6-dimethylphenylimino)methyl]phenol (pKa: 8.85+/-0.30) (0.117 mmol), silver (I) carbonate (16.27 mg, 0.058 mmol), and THF (2 ml) were reacted at room temperature during 2 h. The solvent was evaporated and crude reaction product purified on a chromatography column to give an orange-brown complex. Yield 22%.

With the complex challenges of chemical substances, we look forward to future research findings about (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium

Reference£º
Patent; Telene S.A.S.; US2011/65925; (2011); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Name is Dichlorotris(triphenylphosphino)ruthenium (II), as a common heterocyclic compound, it belongs to ruthenium-catalysts compound, and cas is 15529-49-4, its synthesis route is as follows.,15529-49-4

General procedure: To a round-bottomed flask with a stir bar was placed with [Ru(PPh3)3Cl2] (868 mg, 2.0 mmol) under the nitrogen. Pre-dried THF(10 mL) was added and the resulting mixture was stirred at room temperature. Then salen-enH2 (536 mg, 2.0 mmol) and a little excess of Et3N (252 mg, 2.5 mmol) in THF (5 mL) were added. The reaction mixture was stirred at room temperature overnight. After removal of solvents, CH2Cl2 (15 mL) was added and the solution was filtered through cilite. The filtrate was concentrated and the residue was washed with Et2O (5mL 2) and hexane (5 mL 2) to give the desired product. Recrystallization from CH2Cl2/Et2O (1:2) afforded green block-shaped crystals of [RuCl(PPh3)(salen)] (3) suitable for X-ray diffraction in three days. Yield: 1011 mg, 76% (based on Ru).

With the complex challenges of chemical substances, we look forward to future research findings about Dichlorotris(triphenylphosphino)ruthenium (II)

Reference£º
Article; Tang, Li-Hua; Wu, Fule; Lin, Hui; Jia, Ai-Quan; Zhang, Qian-Feng; Inorganica Chimica Acta; vol. 477; (2018); p. 212 – 218;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

As a common heterocyclic compound, it belongs to ruthenium-catalysts compound, name is Dichlorotris(triphenylphosphino)ruthenium (II), and cas is 15529-49-4, its synthesis route is as follows.,15529-49-4

c) Preparation of the Complex Dichloro bis[3-(Diphenylphosphino)-1-propylamine]Ruthenium; ([RuCl2(L-2)2]). Under argon, a round-bottomed Schlenck flask, equipped with a magnetic stirring bar, was charged with RuCl2(PPh3)3 (1.028 g, 1.07 mmol) and with a solution of 3-(diphenylphosphino)-1-propylamine (566.8 mg, 2.33 mmol) in toluene (5 mL). More toluene (5 mL) was added to rinse. Then the dark-brown solution was heated in an oil bath at 100 C. for 16 h. The resulting brick-orange suspension was cooled to room temperature, and added to pentane (50 mL) with stirring. The yellow solid was collected by filtration, washed with pentane (2¡Á3 mL) and dried in vacuo to provide the desired complex (672.6 mg, 1.02 mmol, 95%) as a yellow-mustard solid. 31P{1H}-NMR analysis showed the presence of two species. 1H-NMR (CD2Cl2): delta (A) 7.19 (t, J=7.2 Hz, 4H), 7.14 (m, 8H), 7.05 (t, J=7.2 Hz, 8H), 3.28 (brs, 4H), 3.02 (brs, 4H), 2.66 (m, 4H), 2.0 (m, 4H). 13C-NMR (CD2Cl2): delta (A) 138.4 (t, J=19.2 Hz, Carom), 134.2 (t, J=4.8 Hz, CHarom), 129.0 (CHarom), 127.5 (t, J=4.8 Hz, CHarom), 41.3 (CH2), 26.9 (t, J=13.6 Hz, CH2), 24.7 (CH2). 31P{1H}-NMR (CD2Cl2): A (82%) delta=33.5 ppm (s), B (18%) delta=49.8 ppm (s).

With the complex challenges of chemical substances, we look forward to future research findings about 15529-49-4,belong ruthenium-catalysts compound

Reference£º
Patent; SAUDAN, Lionel; Dupau, Philippe; Riedhauser, Jean-Jacques; Wyss, Patrick; US2008/71121; (2008); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Dichlorotris(triphenylphosphino)ruthenium (II), cas is 15529-49-4, it is a common heterocyclic compound, the ruthenium-catalysts compound, its synthesis route is as follows.,15529-49-4

PPh3)3RuCI2 (1 eq., 0.575 g, 0.6 mmol) and 1 ,1-bis-2-methylphenyl-prop-2-yn-1-ol (compound C, 1 .5 eq., 0.213 g, 0.9 mmol) were added in 4 ml HCI/dioxane solution (0.15 mol/l). The solution was heated to 90C for 3 hour, after which the solvent was removed under vacuum. Hexane (20 ml) was added to the flask and the solid was ultrasonically removed from the wall. The resulting suspension was filtered and washed two times using hexane (5 ml). The remaining solvent was evaporated affording a red-brown powder; 0.52 g (Yield: 95 %). The product was characterized by NMR spectra H and P. 1H NMR (300 MHz, CDCI3, TMS): delta 7.56 (dd, 1 1 H), 7.37 (t, 6 H), 7.21-7.31 (m, 13 H), 7.09 (tetra, 3 H), 6.95 (t, 3 H), 6.47 (t, 1 H), 6.14 (s, 1 H), 2.20 (s, 3 H), 1.66 (s, 3 H). 31 P NMR (121.49 MHz, CDCI3): delta 29.33.

With the rapid development of chemical substances, we look forward to future research findings about Dichlorotris(triphenylphosphino)ruthenium (II)

Reference£º
Patent; GUANG MING INNOVATION COMPANY (WUHAN); W.C. VERPOORT, Francis; YU, Baoyi; WO2014/108071; (2014); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI