Category: ruthenium-catalysts

Name is Dichlorotris(triphenylphosphino)ruthenium (II), as a common heterocyclic compound, it belongs to ruthenium-catalysts compound, and cas is 15529-49-4, its synthesis route is as follows.,15529-49-4

General procedure: Diphosphine ligand (2.0 mmol) was dissolved in 10 mL of dichloromethane and the solution was added dropwise to a stirred solution of RuCl2(PPh3)3 (1.0 mmol) in 10 mL of dichloromethane. The reaction mixture was stirred approximately for 50 min at room temperature. The brown solution was filtered to remove the insoluble impurities. The solvent was reduced by a vacuum and the product was then precipitated by adding n-hexane. The yellow solid was filtered and washed three times with 20 mL of diethyl ether.

With the complex challenges of chemical substances, we look forward to future research findings about Dichlorotris(triphenylphosphino)ruthenium (II)

Reference£º
Article; Al-Noaimi, Mousa; Warad, Ismail; Abdel-Rahman, Obadah S.; Awwadi, Firas F.; Haddad, Salim F.; Hadda, Taibi B.; Polyhedron; vol. 62; (2013); p. 110 – 119;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

As a common heterocyclic compound, it belongs to quinuclidine compound,Quinuclidine-4-carboxylic acid hydrochloride,40117-63-3,Molecular formula: C8H14ClNO158,mainly used in chemical industry, its synthesis route is as follows.,15529-49-4

Compound 10 (628.5 mg, 1.0 mmol) and degassed morpholine (15 mL) were placed in a 100-mL Young-Schlenk container substituted with argon gas. Thereafter, the Young-Schlenk container was placed in an oil bath, and heated to 120 C. while stirring the components in the Young-Schlenk container, thereby causing a reaction. The progress of the reaction was confirmed by TLC, and the heating was stopped after two hours. Subsequently, the morpholine in the reaction mixture restored to room temperature (25 C.) was removed after collection with a liquid nitrogen trap under reduced pressure (0.1 to 2 mmHg). At this time, the reaction mixture was sufficiently stirred, and the Young-Schlenk container was immersed in water at room temperature (25 C.) to prevent cooling of the Young-Schlenk container by the heat of vaporization. (0255) After sufficiently removing the morpholine, dichlorotris(triphenylphosphino)ruthenium (II) (958.8 mg, 1.0 mmol) and dehydrated toluene (20 mL) were added while introducing argon gas into the container, and the mixture was heated to 110 C. using an oil bath, thereby causing a reaction. The heating was stopped after two hours, and the reaction mixture was restored to room temperature (25 C.). (0256) Subsequently, dehydrated hexane (40 mL) was added to the reaction mixture in an argon gas atmosphere. Thereafter, the whole mixture, including the hexane layer and the toluene layer, in the Young-Schlenk container was stirred and completely mixed. After leaving the mixture unattended for an hour, the generated purple substance was filtered out in an argon atmosphere while being washed with dehydrated diethylether, thereby obtaining a crude product. (0257) Subsequently, the resulting crude product was subjected to column chromatography (developing solvent: chloroform/THF=10/1) in which silica gels were accumulated to about 10 cm, thereby removing a compound with high polarity. The effluent was collected to a flask and the collection was continued until the color of the purple liquid was slightly diluted. After this operation, the solution collected in the recovery flask was rapidly concentrated by an evaporator, thereby obtaining 563.7 mg (0.73 mmol, 73%) of substantially pure Compound 2f (RUPCY3) as a purple substance. (0258) The spectral data of Compound 2f (RUPCY3) is shown below. (0259) 1H NMR (600 MHz, CDCl3): delta 8.12 (d, 2H, J=8.2 Hz, C12H6N2), 7.86 (d, 2H, J=8.2 Hz, C12H6N2), 7.80 (s, 2H, C12H6N2), 4.05 (d, 4H, J 35=7.6 Hz, PCH2), 2.42-2.51 (br, 4H, C6H11), 2.31 (d, 4H, J=11.0 Hz C6H11), 2.12 (d, 4H, J=12.4 Hz, C6H11), 1.61-1.94 (m, 20H, C6H11), 1.18-1.37 (m, 12H, C6H11). 13C NMR (151 MHz, CDCl3): delta 163.6, 149.3, 132.6, 128.6, 125.3, 121.8, 41.4, (d, 1JPC=23.1 Hz) 36.6 (t, 1JPC=7.2 Hz), 30.7, 29.4, 27.8, 27.6, 26.4. 31P{1H} NMR (243 MHz, CDCl3): delta 56.8. HRMS (ESI, (M-Cl)+) Calcd for C38H54ClN2P2Ru+: 737.2494. Found m/z=737.2483. (0260) FIG. 2 shows the result of an X-ray single crystal structural analysis (Oak Ridge Thermal Ellipsoid Plot) of Compound 2f.

With the complex challenges of chemical substances, we look forward to future research findings about Dichlorotris(triphenylphosphino)ruthenium (II),belong ruthenium-catalysts compound

Reference£º
Patent; National University Corporation Nagoya University; Saito, Susumu; Noyori, Ryoji; Miura, Takashi; Naruto, Masayuki; Iida, Kazuki; Takada, Yuki; Toda, Katsuaki; Nimura, Sota; Agrawal, Santosh; Lee, Sunkook; (42 pag.)US9463451; (2016); B2;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Name is (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium, as a common heterocyclic compound, it belongs to ruthenium-catalysts compound, and cas is 246047-72-3, its synthesis route is as follows.,246047-72-3

To a dry 100 mL round-bottom flask containing a magnetic stirbar, under argon, was added 1.79 g (2.1 mmol, 1.0 equiv) [5], CuCl (521 mg, 5.28 mmol, 2.51 equiv), and 25 mL of anhydrous CH2Cl2. Ligand precursor [2] (403 mg, 2.1 mmol, 1.0 equiv) was added to the reddish solution in 20 mL of CH2Cl2 at room temperature. A reflux condenser was added and the mixture was heated for 70 minutes, under argon. The crude product was concentrated and loaded onto silica gel and eluted with 2:1 pentane:CH2Cl2 then 1:1 pentane:CH2Cl2 to remove a dark green band. The column was washed with CH2Cl2, then Et2O. The green and yellow bands were combined and concentrated under reduced pressure to yield a dark green solid. The solvents are removed under reduced pressure and the solid was crystallized from hexane to yield 1.07 g (1.70 mmol, 85%) of [6]. 1H NMR (300 MHz, CDCl3) delta: 16.56 (s, 1H, Ru=CHAr), 7.48 (m, 1H, aromatic CH), 7.07 (s, 4H, mesityl aromatic CH), 6.93 (dd, J=7.4 Hz, 1.6 Hz, 1H, aromatic CH), 6.85 (dd, J=7.4 Hz, 1H, aromatic CH), 6.79 (d, J=8.6 Hz, 1H, aromatic CH) 4.90 (septet, J=6.3 Hz, 1H, (CH3)2CHOAr), 4.18 (s, 4H, N(CH2)2N), 2.48 (s, 12H, mesityl o-CH3), 2.40 (s, 6H, mesityl p-CH3), 1.27 (d, J=5.9 Hz, 6H, (CH3)2CHOAr. 13C NMR (75 MHz, CDCl3) delta: 296.8 (q, J=61.5 Hz), 211.1, 152.0, 145.1, 145.09, 138.61, 129.4 (d, JNC 3.9 Hz), 129.3, 129.2, 122.6, 122.1, 122.8, 74.9 (d, JOC 10.7 Hz), 51.4, 30.9, 25.9, 21.01.

With the complex challenges of chemical substances, we look forward to future research findings about (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium

Reference£º
Patent; MATERIA, INC.; Pederson, Richard L.; Woertink, Jason K.; Haar, Christopher M.; Gindelberger, David E.; Schrodi, Yann; (13 pag.)US9504997; (2016); B2;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

As a common heterocyclic compound, it belongs to quinuclidine compound,Quinuclidine-4-carboxylic acid hydrochloride,40117-63-3,Molecular formula: C8H14ClNO367,mainly used in chemical industry, its synthesis route is as follows.,246047-72-3

A suspension of 500 mg (0.59 mmol) of [RuCl2(PCy3) (ImH2Mes)(phenylmethy- lene)] (commercially available from Sigma-Aldrich Inc., St. Louis, USA), 60 mg (0.61 mmol) copper chloride and 100 mg (0.64 mmol) 8-vinylquinoline (prepared according to G.T. Crisp, S. Papadopoulos, Aust. J. Chem. 1989, 42, 279-285) in 40 ml methylene chloride was stirred at room temperature for 90 min. The reaction mixture was evaporated to dryness and the isolated crude product purified by silica gel chromatography (hexane / ethyl acetat 2:1) to yield 255 mg (70%) of the title compound as green crystals. MS: 584.4 (M-Cl+). 1H-NMR (300 MHz, CD2Cl2): 2.36 (s, 6H); 2.40 (s, 12H); 4.04 (s, 4H); 7.01 (s, 4H); 7.19 (dd, J=8.4, 4.9Hz, IH); 7.34 (t, J=7.7Hz, IH); 7.51 (d, J=7.1Hz, IH); 8.08-8.18 (m, 2H); 8.26 (dd, J=4.8, 1.3Hz, IH); 16.95 (s, IH). Anal, calcd. for C3IH33N3Cl2Ru: C, 60.09; H, 5.37; N, 6.78; Cl, 11.44. Found: C, 60.06; H, 5.75; N, 6.16; Cl, 10.90.

With the synthetic route has been constantly updated, we look forward to future research findings about (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium,belong ruthenium-catalysts compound

Reference£º
Patent; F. HOFFMANN-LA ROCHE AG; WO2008/644; (2008); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

As a common heterocyclic compound, it belongs to quinuclidine compound,Quinuclidine-4-carboxylic acid hydrochloride,40117-63-3,Molecular formula: C8H14ClNO239,mainly used in chemical industry, its synthesis route is as follows.,15529-49-4

In a glove box, [RuCl2(PPh3)3] (0.25 mmol) was added to a schlenk flask equipped with a magnetic stir bar. The flask was then attached to a schlenk line and 3.4 mL of freshly distilled toluene added. The mixture was then rapidly stirred. A 1.7 mL toluene solution of Ph2PCH2CH2NH2, (0.50 mmol) in an NMR tube was then added via a cannula. Any residue in the NMR tube and cannula was washed into the flask with 1.7 mL of toluene. The light yellow mixture was then heated at 100 C. for 6 h. The yellow suspension that resulted was allowed to cool to RT before collecting the precipitate by filtration under Argon. The precipitate was then washed with 10.0 mL portions of toluene, three times (until colorless). The yellow solid was then dried in vacuo. Yield: 90%. Note: Excessive scraping of the product should be minimised to prevent the build-up of static electricity

With the complex challenges of chemical substances, we look forward to future research findings about Dichlorotris(triphenylphosphino)ruthenium (II),belong ruthenium-catalysts compound

Reference£º
Patent; THE GOVERNORS OF THE UNIVERSITY OF ALBERTA; Bergens, Steven; John, Jeremy M.; US2014/163225; (2014); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Name is Dichlorotris(triphenylphosphino)ruthenium (II), as a common heterocyclic compound, it belongs to ruthenium-catalysts compound, and cas is 15529-49-4, its synthesis route is as follows.,15529-49-4

General procedure: To a round-bottomed flask with a stir bar was placed with [Ru(PPh3)3Cl2] (868 mg, 2.0 mmol) under the nitrogen. Pre-dried THF(10 mL) was added and the resulting mixture was stirred at room temperature. Then salen-enH2 (536 mg, 2.0 mmol) and a little excess of Et3N (252 mg, 2.5 mmol) in THF (5 mL) were added. The reaction mixture was stirred at room temperature overnight. After removal of solvents, CH2Cl2 (15 mL) was added and the solution was filtered through cilite. The filtrate was concentrated and the residue was washed with Et2O (5mL 2) and hexane (5 mL 2) to give the desired product. Recrystallization from CH2Cl2/Et2O (1:2) afforded green block-shaped crystals of [RuCl(PPh3)(salen)] (3) suitable for X-ray diffraction in three days. Yield: 1011 mg, 76% (based on Ru).

With the complex challenges of chemical substances, we look forward to future research findings about Dichlorotris(triphenylphosphino)ruthenium (II)

Reference£º
Article; Tang, Li-Hua; Wu, Fule; Lin, Hui; Jia, Ai-Quan; Zhang, Qian-Feng; Inorganica Chimica Acta; vol. 477; (2018); p. 212 – 218;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.15529-49-4,Dichlorotris(triphenylphosphino)ruthenium (II),as a common compound, the synthetic route is as follows.

To a solution of [Ru(PPh3)3Cl2] (868?mg, 2.0?mmol) in THF (10?mL) was added a solution of N,O-LH-NO2 (972?mg, 2.0?mmol) and Et3N (404?mg, 4.0?mmol) in EtOH (5?mL), and then the mixture was heated at 90?C with stirring overnight, during which there was a color change from brown to green. After removal of solvents in vacuo, the residue was extracted with CH2Cl2 (5?mL?*?2) and the solution was filtered. The clearly green filtrate was layered with Et2O (20?mL) at room temperature, and dark green block-shaped crystals of trans-[RuCl(PPh3)(kappa2-N,O-L-NO2)2]¡¤Et2O (2) were obtained in three days. Yield: 1356?mg, 71% (based on Ru).

15529-49-4, As the paragraph descriping shows that 15529-49-4 is playing an increasingly important role.

Reference£º
Article; Tang, Li-Hua; Wu, Fule; Lin, Hui; Jia, Ai-Quan; Zhang, Qian-Feng; Inorganica Chimica Acta; vol. 477; (2018); p. 212 – 218;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

246047-72-3, (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium is a ruthenium-catalysts compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

After a 50 mL two-necked flask was replaced with argon, the ligands 3bx (10 mmol), CuCl (30 mmol, 3 eq) and 30 mL of dry DCM were sequentially added and the mixture was purged three times with argon to protect the closed system with argon balloon. Ruthenium complex 1b (12 mmol) was added under argon atmosphere, and the reaction was carried out at room temperature for 0.5 hour. After the reaction was completed, silica gel was added to the filtrate to produce sand. The crude product was obtained by silica gel column chromatography and then washed with methanol or pentane-DCM to obtain 4bx as a green solid, yield: 65%.

246047-72-3, 246047-72-3 (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium 11147261, aruthenium-catalysts compound, is more and more widely used in various fields.

Reference£º
Patent; Zannan Science And Technology (Shanghai) Co., Ltd.; Zhan Zhengyun; (102 pag.)CN104262403; (2017); B;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Dichlorotris(triphenylphosphino)ruthenium (II), cas is 15529-49-4, it is a common heterocyclic compound, the ruthenium-catalysts compound, its synthesis route is as follows.,15529-49-4

Compound 6 (604.4 mg, 1.0 mmol) and degassed morpholine (20 mL) were placed in a 100-mL Young-Schlenk container substituted with argon gas. Thereafter, the Young-Schlenk container was placed in an oil bath, and heated to 120 C. while stirring the components in the Young-Schlenk container, thereby causing a reaction. The progress of the reaction was confirmed by TLC, and the heating was stopped after two hours. Subsequently, the morpholine in the reaction mixture restored to room temperature (25 C.) was removed after collection with a liquid nitrogen trap under reduced pressure (0.1 to 2 mmHg). At this time, the reaction mixture was sufficiently stirred, and the Young-Schlenk container was immersed in water at room temperature (25 C.) to prevent cooling of the Young-Schlenk container by the heat of vaporization. (0217) After sufficiently removing the morpholine, dichlorotris(triphenylphosphino)ruthenium (II) (958.8 mg, 1.0 mmol) and dehydrated toluene (20 mL) were added while introducing argon gas into the container, and the mixture was heated to 110 C. using an oil bath, thereby causing a reaction. The heating was stopped after three hours, and the reaction mixture was restored to room temperature (25 C.). (0218) Subsequently, dehydrated hexane (40 mL) was added to the reaction mixture in an argon gas atmosphere. Thereafter, the whole mixture, including the hexane layer and the toluene layer, in the Young-Schlenk container was stirred and completely mixed. After leaving the mixture unattended for 15 minutes, the generated purple substance was filtered out in an argon atmosphere while being washed with dehydrated diethylether, thereby obtaining a crude product. (0219) Subsequently, the resulting crude product was subjected to column chromatography (developing solvent: chloroform/ethyl acetate=5/1) in which silica gels were accumulated to about 10 cm, thereby removing a compound with high polarity. The effluent was collected to a flask and the collection was continued until the color of the purple liquid was slightly diluted. After this operation, the solution collected in the recovery flask was rapidly concentrated by an evaporator, thereby obtaining 435.1 mg (0.58 mmol, 58%) of substantially pure Compound 2c (RUPCY2) as a purple substance. (0220) The spectral data of Compound 2c (RUPCY2) is shown below. (0221) 1H NMR (500 MHz, CDCl3): delta 7.86 (d, 2H, J=7.4 Hz, C10H6N2), 7.66 (t, 2H, J=7.5 Hz, C10H6N2), 7.56 (d, 2H, J=7.5 Hz, C10H6N2), 3.87 (d, 4H, J=8.1 Hz, PCH2), 2.41 (br, 4H, C6H11), 2.18 (d, 4H, J=12.1 Hz, C6H11), 2.05 (d, 4H, J=10.9 Hz, C6H11), 1.54-1.81 (m, 20H, C6H11), 1.20-1.34 (m, 20H, C6H11). 13C NMR (150 MHz, CDCl3): delta 163.3, 158.3, 134.1, 122.0, 119.9, 40.5 (d, 1JPC=13.0 Hz), 36.3, 30.3, 29.4, 27.7, 27.5, 26.4. 31P{1H} NMR (241 MHz, CDCl3): delta 54.1. HRMS (ESI, (M-Cl)+) Calcd for C36H54ClN2P2Ru+: 713.2494. Found m/z=713.2476. (0222) FIG. 1 shows a result of X-ray single crystal structural analysis (Oak Ridge Thermal Ellipsoid Plot) of Compound 2c.

15529-49-4 is used more and more widely, we look forward to future research findings about Dichlorotris(triphenylphosphino)ruthenium (II)

Reference£º
Patent; National University Corporation Nagoya University; Saito, Susumu; Noyori, Ryoji; Miura, Takashi; Naruto, Masayuki; Iida, Kazuki; Takada, Yuki; Toda, Katsuaki; Nimura, Sota; Agrawal, Santosh; Lee, Sunkook; (42 pag.)US9463451; (2016); B2;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

(1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium, cas is 246047-72-3, it is a common heterocyclic compound, the ruthenium-catalysts compound, its synthesis route is as follows.,246047-72-3

Example 1Synthesis of Ru complex 4a (H2IMes)(PCy3)Cl2Ru=CHPh (formula lb, 860mg, l .Ommol) and CuCl (270 mg, 2.5mmol, 2.5 eq) were added into a 100 mL of two-neck round-bottom flask filled with inert gas (Ar), and followed by adding DCM (15 mL) and ligand 3a (250 mg, 1.2mmol, 1.2 eq) into the DCM solution at 20-25C. The reaction was stirred until completed in 30-60 min. (monitored by TLC). The reaction mixture was filtered and concentrated, then purified by flash column eluting with a gradient solvent (Pentane/DCM 2/1 to DCM). The purified solid product was washed with methanol, and dried under vacuum to obtain 27mg of green solid product 4a, yield: 4%. The green product was confirmed by 1HNMR. Ru complex (4a) 1HNMR (400 MHz, CDC13): delta 19.09 (s, lH, Ru=CH),7.51-6.70 (m, 13H), 5.31 (m, 1H), 4.30 (d, J = 12.9 Hz, 1H), 4.04 (s, 4H, NCH2CH2N), 3.61 (d, J= 12.9 Hz, 1H), 2.45 (s, 12H), 2.33 (s, 6H).; Example 9 Synthesis of Ru complex 4j The synthetic procedure is the same as in Example 1 in 1.0 mmol scale. 353 mg of green solid product 4j was obtained (yield: 48%). Ru complex (4j) 1H- MR (400 MHz, CDC13): delta 18.88 (s, lH, Ru=CH), 7.57-6.44 (m, 11H), 5.36 (t, J = 13.2 Hz, 1H), 4.16-4.02 (m, 5H), 4.01 (d, J = 13.2 Hz, 1H), 2.75-2.00 (m, 19H), 1.01-0.90 (m, 6H).

246047-72-3 is used more and more widely, we look forward to future research findings about (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium

Reference£º
Patent; ZANNAN SCITECH CO., LTD.; ZHAN, James Zheng-Yun; WO2011/79439; (2011); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI