Ruthenium catalysts

50982-12-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2,the ruthenium-catalysts compound, it is a common compound, a new synthetic route is introduced below.

General procedure: The following common procedure was followed for the synthesesof complexes 1-5: A mixture of the ligand (0.36 mmol) and Ru(1,5-cod)Cl2(0.36 mmol) was dissolved in dry ethanol (10 ml) and the resultingmixture was refluxed for 2 h. The reaction volume was concentratedto a third of its original volume and the suspension was keptat 4 C overnight to give brick red solid which was filtered off,washed with cold ethanol and then diethyl ether. The solid wasdissolved in chloroform and excess of n-hexane was added toinduce the precipitation of the brick red solid product.

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of Dichloro(cycloocta-1,5-diene)ruthenium(II), 50982-12-2

Reference£º
Article; Thangavel, Saravanan; Rajamanikandan, Ramar; Friedrich, Holger B.; Ilanchelian, Malaichamy; Omondi, Bernard; Polyhedron; vol. 107; (2016); p. 124 – 135;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

As a common heterocyclic compound, it belongs to ruthenium-catalysts compound, name is Dichlorotris(triphenylphosphino)ruthenium (II), and cas is 15529-49-4, its synthesis route is as follows.

Synthesis of the new ruthenium promoters 4 and 10 was carried out in this work. For the synthesis of complex 4 a THF solution of the thalium salt of the Schiff base ligand [20] was added the equivalent amount of Cl2Ru(PPh3)3 and the mixture stirred overnight at room temperature. After work-up [11b,20] the solid residue was dissolved in a minimal amount of toluene, reprecipitated with pentane, filtered off, briefly washed on the funnel with pentane and dried in vacuo to afford an orange-brown powder (78% yield) which was stored under inert atmosphere. 1H NMR (300 MHz, CDCl3): delta 2.36 [s, 3H, CH3]; 7.10-7.80 [m, 34H, aryl-CH]; 9.95 ppm (s, 1H, aldimine ligand).

15529-49-4, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,15529-49-4 ,Dichlorotris(triphenylphosphino)ruthenium (II), other downstream synthetic routes, hurry up and to see

Reference£º
Article; Dragutan, Ileana; Ding, Fu; Sun, Ya-Guang; Verpoort, Francis; Dragutan, Valerian; Journal of Molecular Catalysis A: Chemical; vol. 386; (2014); p. 86 – 94;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Name is Dichlorotris(triphenylphosphino)ruthenium (II), as a common heterocyclic compound, it belongs to ruthenium-catalysts compound, and cas is 15529-49-4, its synthesis route is as follows.

A 50 ml three-necked flask equipped with a stirring reflux device was charged with 1 mmol of 2-diethylphosphine aniline,1.3 mmol of o-methoxybenzyl alcohol, 1 mmol2-dicyclohexylphosphine oxide, 1 mmol RuCl2 (PPh3) 3, 1.1 mmol potassium hydroxide, 20 ml benzene and heating at a temperature of 100 C for 18 h under a nitrogen atmosphere,After cooling and filtering, the resulting solid was recrystallized from a mixed solvent of CH 2 Cl 2 and petroleum ether to give product 15 in a yield of 80%.

15529-49-4, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,15529-49-4 ,Dichlorotris(triphenylphosphino)ruthenium (II), other downstream synthetic routes, hurry up and to see

Reference£º
Patent; Luoyang Normal College; Li Hongmei; Xu Chen; Zu Enpu; Xiao Zhiqiang; Han Xin; (12 pag.)CN104804048; (2017); B;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

15529-49-4, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Dichlorotris(triphenylphosphino)ruthenium (II), cas is 15529-49-4,the ruthenium-catalysts compound, it is a common compound, a new synthetic route is introduced below.

General procedure: To a round-bottomed flask with a stir bar was placed with [Ru(PPh3)3Cl2] (868 mg, 2.0 mmol) under the nitrogen. Pre-dried THF(10 mL) was added and the resulting mixture was stirred at room temperature. Then salen-enH2 (536 mg, 2.0 mmol) and a little excess of Et3N (252 mg, 2.5 mmol) in THF (5 mL) were added. The reaction mixture was stirred at room temperature overnight. After removal of solvents, CH2Cl2 (15 mL) was added and the solution was filtered through cilite. The filtrate was concentrated and the residue was washed with Et2O (5mL 2) and hexane (5 mL 2) to give the desired product. Recrystallization from CH2Cl2/Et2O (1:2) afforded green block-shaped crystals of [RuCl(PPh3)(salen)] (3) suitable for X-ray diffraction in three days. Yield: 1011 mg, 76% (based on Ru).

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of Dichlorotris(triphenylphosphino)ruthenium (II), 15529-49-4

Reference£º
Article; Tang, Li-Hua; Wu, Fule; Lin, Hui; Jia, Ai-Quan; Zhang, Qian-Feng; Inorganica Chimica Acta; vol. 477; (2018); p. 212 – 218;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

50982-12-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2,the ruthenium-catalysts compound, it is a common compound, a new synthetic route is introduced below.

The catalyst precursor, preferably [RuCI2(COD)]m (1 eq.) (COD = cis,cis-cycloocta-1 ,5 diene), 1 ,4-bis(diphenylphosphino)butane (1.0-1 .2 eq., preferably 1.0 eq.) and 2-picolylamine (1 .0-1.4 eq., preferably 1.225 eq.) were dissolved in one of the above mentioned solvents, preferably methyl isobutylketone (10-20 ml/g Ru-precursor, preferably 20 ml/g). The mixture was heated to reflux for 3 – 5 hours and then cooled to ambient temperature. The solid precipitate was filtered off and washed with the same solvent that was used for the reaction. A person skilled in the art can determine the cis-/trans- isomeric ratio by NMR. The diastereomeric ratios generated by this method are usually in the range of d.r. (diastereomeric ratio) >98% towards the cis isomer. The same results can be achieved starting with [RuCI2(dmso-KS)3(dmso-KO)], [RuCI2(dmso-KS)4]or [RuCI2(bicyclo[2.2.1 ]hepta- 2,5-diene)]m as precursor

The chemical industry reduces the impact on the environment during synthesis,50982-12-2,Dichloro(cycloocta-1,5-diene)ruthenium(II),I believe this compound will play a more active role in future production and life.

Reference£º
Patent; SYNGENTA PARTICIPATIONS AG; LOTHSCHUETZ, Christian; SAINT-DIZIER, Alexandre Christian; WO2014/166777; (2014); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

301224-40-8, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. (1,3-Dimesitylimidazolidin-2-ylidene)(2-isopropoxybenzylidene)ruthenium(VI) chloride, cas is 301224-40-8,the ruthenium-catalysts compound, it is a common compound, a new synthetic route is introduced below.

HII 65 HII (200mg) and P(0’Pr)3 (5eq) were stirred in for 72h. The crude 65 was recrystallised from DCM/pentane. (400MHz, 298K): 16.05 (d, 1 H, J = 35.3 Hz, C=CH), 10.24 (d, 1 H, J = 9.7 Hz, Ph-H), 6.87-6.83 (m, 2H, Ph-H), 6.78 (s, 1 H, Ph-H), 6.61 (s, 1 H, Ph-H), 6.19-6.16 (m, 2H, Ph- H), 4.67 (brs, 2H, PO-CH-CH3), 4.09-4.06 (m, 1 H, Ph-0-CH-CH3), 4.04 (brs, 1 H, PO- CH-CH3), 3.43-3.40 (m, 1 H), 3.16-3.02 (m, 3H), 2.89 (s, 3H, Mes-CH3), 2.58 (s, 3H, CH3), 2.46 (s, 3H, CH3), 2.42 (s, 3H, CH3), 2.18 (s, 3H, CH3), 1.92 (s, 3H, CH3), 1.48- 0.80 (m, 24H, PO-CH-CH3).31P{1H} (121.49MHz, 298K): 128.7 (s)

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of (1,3-Dimesitylimidazolidin-2-ylidene)(2-isopropoxybenzylidene)ruthenium(VI) chloride, 301224-40-8

Reference£º
Patent; UNIVERSITY COURT OF THE UNIVERSITY OF ST ANDREWS; CAZIN, Catherine; WO2011/117571; (2011); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Name is Dichloro[1,3-bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene][[5-[(dimethylamino)sulfonyl]-2-(1-methylethoxy-O)phenyl]methylene-C]ruthenium(II), as a common heterocyclic compound, it belongs to ruthenium-catalysts compound, and cas is 918870-76-5, its synthesis route is as follows.

In a glovebox 13 (800 mg, 1.09 mmol) and AgOCN (374 mg, 2.51 mmol) were suspended in 10 ml of tetrahy-drofuran. The mixture was stirred for three hours at room temperature, and then the solvent was removed under vacuum.The residual was dissolved in dichloromethane and filtered through a short pad of silica gel using dichloromethane/diethylether (9:1) as eluent. The green solution containing complex 14 was concentrated under vacuum and the compoundwas precipitated with pentane at room temperature. The green solid was isolated by cannula filtration and washed threetimes with pentane. The solid was transferred in a glovebox and dried under argon atmosphere (744 mg, 91 % of yield).1H NMR (600.17 MHz, CD2Cl2): delta = 16.25 (br s, 1 H), 7.95 (dd, J = 8.6, 2.2, 1 H), 7.24 (d, J = 2.2, 1 H), 7.14 (br s, 4 H),6.99 (d, J = 8.6, 1 H), 4.94 (sep, J = 6.1, 1 H), 4.19 (s, 4 H), 2.27 (s, 6 H), 2.43 (s, 6 H), 2.41 (s, 12 H), 1.11 (d, J = 6.1,6 H). 13C{1H} NMR (150.91 MHz, CD2Cl2): delta= 295.12, 207.94, 155.24, 143.75, 139.94, 139.26, 135.84, 135.21, 131.02,129.94, 129.29, 121.57, 113.36, 76.88, 51.86, 38.07, 21.17, 20.78, 18.45. HRMS (ESI+), m/z: 767.19735 [M+Na]+;calculated for C35H43N5NaO599RuS: 767.19420.

918870-76-5, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,918870-76-5 ,Dichloro[1,3-bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene][[5-[(dimethylamino)sulfonyl]-2-(1-methylethoxy-O)phenyl]methylene-C]ruthenium(II), other downstream synthetic routes, hurry up and to see

Reference£º
Patent; Bergen Teknologioverf¡ãring AS; Jensen, Vidar Remi; Occhipinti, Giovanni; EP2826783; (2015); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

15529-49-4, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Dichlorotris(triphenylphosphino)ruthenium (II), cas is 15529-49-4,the ruthenium-catalysts compound, it is a common compound, a new synthetic route is introduced below.

A 50 ml three-necked flask equipped with a stirring reflux device was charged with 1 mmol of 2-dicyclohexylphosphine aniline,1.2 mmol of p-chlorobenzyl alcohol, 1 mmol of 1,1′-diphenylphosphinoferrocene, 1 mmol of RuCl2 (PPh3) 3, 1.2 mmol of triethylamine and 20 ml of toluene at a temperature of 110 C. and heated under a nitrogen atmosphere for 24 hAfter cooling and filtration, the resulting solid was recrystallized from a mixed solvent of CH 2 Cl 2 and petroleum ether to give product 20 in a yield of 86%.

The chemical industry reduces the impact on the environment during synthesis,15529-49-4,Dichlorotris(triphenylphosphino)ruthenium (II),I believe this compound will play a more active role in future production and life.

Reference£º
Patent; Luoyang Normal College; Li Hongmei; Xu Chen; Zu Enpu; Xiao Zhiqiang; Han Xin; (12 pag.)CN104804048; (2017); B;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Name is (1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium, as a common heterocyclic compound, it belongs to ruthenium-catalysts compound, and cas is 246047-72-3, its synthesis route is as follows.

Grubbs second generation catalyst (100 mg, 0.117 mmol), 2-[(2,4,6-trimethylphenylimino)methyl]phenol (pKa: 8.84+/-0.30) (0.117 mmol), silver (I) carbonate (16.27 mg, 0.058 mmol), and THF (2 ml) were reacted at room temperature during 2 h. The solvent was evaporated and crude reaction product purified on chromatography column to give an orange-brown complex. Yield 30%.

246047-72-3, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,246047-72-3 ,(1,3-Bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene)dichloro(phenylmethylene)(tricyclohexylphosphine)ruthenium, other downstream synthetic routes, hurry up and to see

Reference£º
Patent; Telene S.A.S.; US2011/65925; (2011); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

50982-12-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2,the ruthenium-catalysts compound, it is a common compound, a new synthetic route is introduced below.

Separately, 200 ml of well dried tetrahydrofuran was fed to a 500 ml flask whose inside had been substituted by argon, and 5 g of dichloro(cyclooctadienyl)ruthenium was injected into the flask and well mixed with the above tetrahydrofuran to obtain a suspension. This suspension was cooled to -78 C. in a stream of argon, and 15 ml of the above synthesized tetrahydrofuran solution of trifluoromethyl cyclopentadienyl sodium was added dropwise to the suspension over 1 hour. The reaction mixture was further stirred at -78 C. for 3 hours and returned to room temperature under agitation over 12 hours. After the reaction mixture was let pass through a neutral alumina column in a stream of argon to be purified and concentrated, it was purified again by a neutral alumina column to obtain 0.2 g of bis(trifluoromethylcyclopentadienyl)ruthenium (yield rate of 30%).

The chemical industry reduces the impact on the environment during synthesis,50982-12-2,Dichloro(cycloocta-1,5-diene)ruthenium(II),I believe this compound will play a more active role in future production and life.

Reference£º
Patent; JSR Corporation; US2006/240190; (2006); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI